A versatile, electrically heated sterilizer under saturated steam of Adjustable pressure of 10 to 20 psi. double walled construction with boiler & steam jacket made of thick stainless steel and gap is filled with high grade glass wool to bring the temp. loss to a minimal level.The outer chamber is made out of thick mild steel.The lid is made of thick stainless steel plate (joint less) or gunmetal plate and can be sealed by a jointless neoprene rubber gasket by wing nuts through hinged bolts by engaging slotted lugs on rim of the cover. Provided with dial pressure gauge, air/ steam release cock, spring loaded safety valve adjustable to any required point from 10 psi to 20 psi with accuracy + 3 psi. A drain cock has also been provided. A double safety valve has also been provided along with inlet. Supplied complete but without dressing bins.

Optional:-

Laboratory Hot Air Ovens, available in two types, inner chamber made of anodized aluminum or stainless steel and out side body made of mild steel duly stowing paint. Temperature range from ambient to 250° C fitted with L shape, Prismatic thermometer fitted at front of the door. Temp. Is controlled by thermostat. Fitted with main switch pilot lamp, Temp. Controlling knob, shelves and workable on 220/230 Volt. AC supply.

Optional at extra cost :

1. Air Circulating Fan ( In big size only)
2. 0-24 hours Timer
3. Digital Tem. Display / indicator
4. Digital Temp. Controller and Indicator
5. Microprocessor PID Digital Temp. Controller cum indicator

Laboratory Hot Air Ovens, available in two types, inner chamber made of anodized aluminum or stainless steel and out side body made of mild steel duly stowing paint.

*  Modification possible as per user requirements.

Double wall construction, inner being made out of highly polished thick stainless steel and outer made out of thick mild steel sheet finished in stoving white enamel paint or staple mat colour combinations. The gap is filled with special glass wool for temp. insulation. The bath is provided with the drain cock to easily drainout the water and clean the chamber when required. A pyramidal shaped cover is provided

Immersion type heating elements are fitted at bottom. Temp. range 5o C above ambient to 80o C with accuracy + 0.5oC to 1oC is controlled by capillary thermostat regulated by a graduated knob on the panel, which is also provided with pilot lamp etc.

The equipment is workable on 220V AC 50Hz single phase. The baths are supplied without racks, thermometer and stirring arrangement.

Optional :-
i) Imported Thermostat "EGO"/"JUMO" German with the accuracy of ±0.5°C.
ii) Digital temp. Indicator -cum - Controller.
iii) Microprocessor PID Digital temp. Indicator- cum- controller.
iv) Digital temp. Indicator.

Double wall construction having both made out of highly polished stainless steel sheet. The gap between the two is filled with glass wool for heat insulation. It is easy to handle table model working on 220 V AC 50 Hz single phase.

Output Capacity
a. Output approx. 4/5 liters per hour.
b. Output approx. 8/9 liters per hour.
c. Output approx. 25/26 liters per hour.

Compact stirring device utilizing a rotating magnetic field applied from below the container. The stirring is accomplished by a taflon rotor placed in the liquid to be stirred. Complete with pilot lamp, plug cord, continuously variable speed regulator The body is made of mild steel duly finished in stoving enamel and mounted with a stainless steel top which serves as a hot plate. Stirring and heating units are properly insulated. In model with heating system temp. is controlled by an energy regulator. An electronic speed controller is also provided. The equipment works on 220V AC 50 HZ single phase.

I) Magnetic stirrer with hot - plate cap. liter, 2liter , 5tliter , 10Liter
II) Magnetic stirrer without heating system 1 liter, 2Liter, 5Liter , 10Liter.
ii) Magnetic stirrer with hot plate & energy regulator 1lliter , 2liter , 5liter , 10liter.
Complete with taflon coated magnet.

Light in weight and heat resistant our quality range of Laminar Air Flow Horizontal is offers in industry leading prices. These are portable and easy to handle and are used for filtering the air and eradicating germs and allergens from the air. Its table top is covered with non glaring laminated sheet or stainless steel sheet, while the side panels are fixed and are made out of transparent acrylic sheet. Further, a two legs table top and two table supports are detachable and can be taken out and fixed within minutes, front door can be kept full open/half open, fully closed as desired. The equipment is fitted with safety attachments of international Standards.

*  Vertical Flow Laminar  Bench also available.

Laboratory hot plates are available in round and rectangular shapes. Body is fabricated out of thick mild steel sheet duly finished in stoving enamel paint. The hot plate made of cast iron, nicely & Precisely machined & smoothed duly finished in heat resistant black paint is firmly mounted on the body. Heavy duty heating elements are securely layed under the plate to operate on 220 V AC 50 Hz single phase. Temp. is controlled by a three-heat rotary switch along with an indicator lamp for the mains and cord & plug.

A) HOT PLATE : (ROUND) Single
Specifications as above with 20 cm.(8") dia. Moulded top.

B) HOT PLATE (Round) Double
As above but with two plates of 20 cm (8") dia. having independent pilot lamps & switches

We are into a business of manufacturing and offering the clients with huge range of Fume Hoods that is fabricated out of thick wooden board. It designed to throw out all toxic/harmful vapours & fumes and hence protecting costly instruments and the persons working in the lab. Outer wall is finished with sunmica and the inner portion with epoxy paint. Moreover, the working table top is acid/alkali resistant and a small wash basin with connections provided for inlet and outlet of water. The front door moves vertically up and down with concealed counter balanced weights. The unit is fitted with fluorescent light and a gas cock for gas/air supply. The front facing panel is fitted with 15/5 Amp socket with switches for exhaust system and fluorescent light. It works on 220 volts AC. 50Hz supply.

Optional:

•High CFM exhaust System (for duct exceeding 10 feet in length)

•S. S. Lining on work bench.

•PVC Fume Duct (per ft.)

Also Available in :

1.M. S. Powder Coated
2.Stainless Steel